Ultrasonic Flow Meters

20+ Years Manufacturing Experience

Support

  • Hydrologic QSD6537 Ultrasonic area velocity sensor

    Only QSD6537 sensor is a submerged doppler sensor to continuously measure flow rate , depth, conductivity in open channels, partially filled pipes, rivers, streams, culverts, canals and others . It is designed for sewage, stormwater and stream flow applications. QSD6537 Area-Velocity Flow Meter ...
    Read more
  • Installation for LMU ultrasonic level meter

    1. general hintsInstallation must be carried out by trained person in accordance with the manual. The temperature of the process may not exceed 75℃,and the pressure may not exceed -0.04~+0.2MPa. The use of metallic fittings or flanges is not recommended. For exposed or sunny locations a protect...
    Read more
  • RC82 heat meter features

    Ultrasonic heat BTU meter For Large Diameter Pipe 1. calculator can be hung at the body or installed separately. 2. Internal 3.6V high capacity lithium battery,external AC220V or DC24V optional; 3. Unique design for fluid structure to improve measuring accuracy and stability and reduce the requi...
    Read more
  • DF6100-EC clamp on doppler flow meter transmitter installation

    Mount the clamp on wastewater flow meter transmitter in a location that is: 1. Where little vibration exists 2. Protected from falling corrosive fluids 3. Within ambient temperature limits -20 to +60°C 4. Out of direct sunlight. Direct sunlight may increase transmitter temperature to above the ma...
    Read more
  • Industrial transit-time ultrasonic flow meter for clean and pure water solution

    At present, all of our Transit-Time ultrasonic flow meters are used for liquid flow measurement and The measured pipe must be full water pipe. Transit time liquid flow meter often used in water supply plants, HVAC application, pharmaceutical factory, food factory, beverage industry, metallurgy in...
    Read more
  • Install Important Tips for SC7 serial flange type water meter

    1. Pay attention to the seal to prevent leakage. 2. To pay attention to the instrument’s direction must be consistent with the actual flow direction 3. Note not let the gasket protruding into the pipe after the installation 4. The instrument is installed in the open pipe valve, pay particul...
    Read more
  • Installation steps for SC7 serial ultrasonic water meter

    To cut off the installation instrument place of water supply pipe, Set aside installation position of meter and threaded for union. Keep the threaded for union screwed to the water supply pipe opening. Align the instrument with the connection accessories;use Matching seal ring between instrument...
    Read more
  • Several common error installation methods for SC7 serial ultrasonic smart water meter

    1. When installation, please screw the pipe nut with a wrench. Do not use hand holding the plastic box body of calculator and then use the wrench to tighten the nut, because it may cause damage. 2. At a vertical installation scenario the heat meter needs to be installed on the flow upward stra...
    Read more
  • The calibration of UOC color screen ultrasonic open channel flow meter

    The instrument should be calibrated indoor before installation to ensure the normal performance. General consideration 1. The open channel flowmeter should be checked indoors before installation to ensure the normal performance of the meter. 2. Align the ultrasonic probe of the open channel f...
    Read more
  • What are the limitations of transit time portable ultrasonic flowmeters ?

    The liminations as below . 1. Portable ultrasonic liquid flowmeter ( Transit-Time ) can only be used for clean liquids like water, beer, chilled water, sea water, etc ; 2.  Clamp on transducers cannot measure the pipes of thick liner or scarling, concavo-convex and corrosion pipes ; 3.  Portable ...
    Read more
  • How to use the flow rate frequency output ?

    Only For Flow Rate Output. TF1100-EP also can provide a frequency output transmitter function. The find accessory OCT output connect cable, white is +, black is GND, refer to below wiring diagram Figure 5.1, A, B is DC power supply based on pulse receiver voltage, 5-24V is allowable. C,D is pulse...
    Read more
  • How to use the 4-20mA output ?

    Refer to Menu 53, 54, 55, 56, 57, 58. Possessing a current loop output exceeding an accuracy of 0.1%, the TF1100 is programmable and configurable with multiple output modules such as 4 ~20mA or 0~20mA. Select in Window M54. For details, please refer to Part 4 – Windows Display Explanations. In Wi...
    Read more

Send your message to us: